Ibase SI-28 Manual do Utilizador Página 1

SI-28 Series User Manual 2011 November V1

10 Specification System Mainboard IB-828 Construction Aluminum Chassis Color Black / White Storage 2.5” 80GB SATA HDD x 1 Mounting Wall mount Dimens

11 Mounting SI-28 to the Wall You can install SI-28 on wood, drywall surface over studs, or a solid concrete or metal plane directly. Ensure the i

12 Mounting to hollow walls  Method 1: Wood surface – A minimum wood thickness – 38mm (1.5in.) by 25.4 cm (10in.) – of high, construction – grade

13 Exploded view of the SI-28 assembly Parts description Part NO. Description Part NO. Description 1 Heat sink 2 IB828 3 HDD tray bracket 4 HDD 5

14 Installation Installing the memory The IB828 board supports one DDR2 memory socket that can support up to 4GB memory size, DDR2 533/667/800 (w/o

15 Installing the CPU The IB828 board supports a Socket AM2 (940-pin) processor socket for AMD Athlon™ 64 / Athlon™ 64 x2 (dual core) / Sempron™ pro

16 Setting Jumper Jumpers are used on IB828 to select various settings and features according to your needs and applications. Contact your supplier

17 JP4, JP5, JP6: RS232/422/485 (COM2) Selection COM1 is fixed for RS-232 use only. COM2 is selectable for RS232, RS-422 and RS-485. The following d

18 BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the board. BIOS Introduction The Award BIOS

19 The section below the setup items of the Main Menu displays the control keys for this menu. At the bottom of the Main Menu just below the contr

2 Copyright © 2011 IBASE Technology INC. All Rights Reserved. No part of this manual, including the products and software described in

20 Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the syst

21 set the current time. The time format is: Hour: 00 to 23 Minute: 00 to 59 Second: 00 to 59 IDE Channel Master/Slave The onboard PCI IDE connec

22 errors All, But Diskette: The system boot will not be halted for a disk error; it will stop for all other errors. All, But Disk/Key: The system

23 Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to yo

24 Quick Power On Self Test When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enabled,

25 APIC Mode APIC stands for Advanced Programmable Interrupt Controller. The default setting is Enabled. MPS Version Control for OS This option is

26 Advanced Chipset Features This Setup menu controls the configuration of the chipset.

27 PCIE Configuration The fields under PCIE Configuration features settings for Primary Dual Slot Config, GPP Slots Power Limit, GFX ports, GPPs an

28 Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. The first screen shows three main it

29 Onboard Serial Port These fields allow you to select the onboard serial ports and their addresses. The default values for these ports are: Seria

3 Table of Contents Acknowledgments ... 6 Accessories

30 Power Management Setup ACPI Suspend Type The default setting of the ACPI Suspend mode is S1(POS). C2 Disable/Enable The default setting of this

31 Video Off Method This field defines the Video Off features. There are three options. V/H SYNC + Blank: Default setting, blank the screen and turn

32 PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must

33 PC Health Status This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds and vol

34 Frequency/Voltage Control This section shows the user how to configure the processor frequency. Spread Spectrum This field sets the value of

35 Load Fail-Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default setti

36 Driver Installation This section describes the installation procedures for software and drivers under the Windows 2000 and Windows XP. The sof

37 2. Click AMD 780E+ATI Radeon E4600 Serial Graphis Drivers. 3. In the Welcome screen, click Next to continue. Then, in the License Agreement scre

38 4. When the Select Components screen appears, click Express: Recommended, in selecting the component that you want to install. 6. Setup is now

39 Realtek High Definition Codec Audio Driver Installation 1. Insert the CD that comes with the board. Click System and click SI-28/IB828 Drivers.

4 Safety Information Your SI-28 is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensu

40 3. In the Welcome screen, click Next to continue. After the driver installation, click Finish on the next screen to restart the computer.

41 LAN Driver Installation 1. Insert the CD that comes with the board. Click System and click SI-28/IB828 Drivers. 2. Click Realtek GbE_FE Etherne

42 3. When the Welcome screen of the InstallShield Wizard appears, click Next to continue. 4. On the next screen, you are asked to click Install t

43 5. Installation is now complete, click Finish to exit the InstallShield Wizard.

44 Appendix ~This page is intentionally left blank~

5 CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. D

6 Acknowledgments  Award is a registered trademark of Award Software International, Inc.  PS/2 is a trademark of International Business Machine

7 Accessories a. Power Cord x 1 b. System Manual x 1 c. Driver CD x 1 d. Power Brick x 1

8 Components I/O View Refer to the diagram below to identify the components on this side of the system. The power switch allows powering ON and O

9 The stereo audio jack (3.5mm) is used to connect the system’s audio out signal to amplified speakers or headphones. LAN The eight-pin RJ-45 LAN